Intergraph SmartPlant 3D Comparative analysis of tie-in calculations for the pipeline at the designed CDU/VDU complex of the Omsk refinery based on 3D modeling
https://doi.org/10.31660/0445-0108-2019-1-58-66
Abstract
The article is devoted to the problem of strength loads when inserting a branch into the main line. We have carried out the calculations in manual form and with the help of a domestic software product START, specializing in pipeline calculations. 3D model of pipelines was designed to solve the problem and 3D model visualized using software product the Intergraph SmartPlant 3D. The results obtained in the development of the model made it possible to establish the most optimal characteristics of the pipeline tie-in for strength loads and to identify the need to use reinforcement of this tie-in. In the course of the research we have studied significant aspects of strength calculations, as well as features of usage of specialized software products. The calculation was used in the actual design of the CDU/VDU complex of the Omsk refinery.
About the Authors
Igor N. Kvasov
Omsk State Technical University
Russian Federation
Candidate of Economics, Professor, Dean of the Faculty of Transport of Oil and Gas
Russian Federation
Candidate of Economics, Professor, Dean of the Faculty of Transport of Oil and Gas
Michael A. Aleksandrov
Industrial University of Tyumen
Russian Federation
Candidate of Engineering, Associate Professor at the Department of Transportation of Hydrocarbon Resources
Russian Federation
Candidate of Engineering, Associate Professor at the Department of Transportation of Hydrocarbon Resources
Andrey V. Zanin
Omsk State Technical University
Russian Federation
Postgraduate at the Department of Hydromechanics and Transport Machines
Russian Federation
Postgraduate at the Department of Hydromechanics and Transport Machines
Maria Yu. Zemenkova
Industrial University of Tyumen
Russian Federation
Candidate of Engineering, Associate Professor at the Department of Transportation of Hydrocarbon Resources
Russian Federation
Candidate of Engineering, Associate Professor at the Department of Transportation of Hydrocarbon Resources
References
1. Квасов И. Н. Анализ систем обнаружения утечек в магистральном нефтепроводе. Инженерное дело: Взгляд в будущее. – Омск, 2016. – С. 33–34.
2. Stress Analysis for the Tie-in Girth Weld of X90 / Yan Zhou [et al.] // Materials Science Forum. – 2016. – Vol. 50. – Р. 889–893. DOI: 10.4028/www.scientific.net/MSF.850.889
3. Abid M., Siddique M. Numerical simulation of the effect of constraints on welding deformations and residual stresses in a pipe–flange joint / / Modelling and Simulation in Materials Science and Engineering. – 2005. – Vol. 13, Issue 6. – Р. 919-933.
4. Повышение надежности и эффективности технологического режима сети нефтесбора / Ю. Д. Земенков [др.] // Трубопроводный транспорт: теория и практика. – 2011. – № 1. – С. 27–30.
5. Торопов С. Ю., Земенков Ю. Д., Подорожников С. Ю. Повышение экологической надежности ремонта трубопроводов в сложных природно-климатических условиях // Газовая промышленность. – 2015. – № S1 (720). – С. 95–98.
6. Занин А. В. Моделирование парной регрессии и проверка ее качества на основе анализа // Транспортное дело России. – 2017. – № 6. – С. 20–26.
7. Zanin A. V., Milke A. A., Kvasov I. N. Hydrocarbons pipeline transportation risk assessment / / Metrology, standartization, quality: Theory and practice (MSQ-2017) IOP Conf. Series: Journal of Physics: Conf. Series 998 (2018) 012043. – 2018. – Available at: https://doi.org/10.1088/1742–6596/998/1/012043.
Review
For citations:
Kvasov I.N., Aleksandrov M.A., Zanin A.V., Zemenkova M.Yu. Intergraph SmartPlant 3D Comparative analysis of tie-in calculations for the pipeline at the designed CDU/VDU complex of the Omsk refinery based on 3D modeling. Oil and Gas Studies. 2019;(1):58-66. (In Russ.) https://doi.org/10.31660/0445-0108-2019-1-58-66
Views:
467
Email this article 
Post a Comment 